,

ColibriNANO USB SDR Receiver 0.1 to 55 MHz

Availability:

Out of stock


ColibriNano takes USB dongle SDR receivers to a new level. This is a direct sampling, high quality SDR receiver covering 100 kHzĀ toĀ 55 MHzĀ with up to 3Ā MHz sampleĀ rate in a sturdy aluminium USB stick.

 

354 $

  • EUR: 325 €
  • SEK: 3 772 kr.

Out of stock

The ColibriNANO opens new horizons for HF band enthusiasts, thanks to its 14-bit ADC, which provides a ~110 dB BDR and up to 3 MHz sample rate. A 0.5 ppm local oscillator gives the ColibriNANO a great frequency stability.

Using the ColibriNANO remotely, located in a rural area will let you receive weak signals otherwise impossible to hear in the noise. Remote control your Colibri NANO from anywhere over the internet using our RPI server

The ColibriNANO operated by ExpertSDR2 software and compatible with popular HAM software such as HDSDR, SDRSharp via the ExtIO library.

ColibriNANO Block Diagram

The ColibriNANO features a Texas Instruments ADS4145 14 bit direct sampling ADC and a built in 55 MHz low pass filter that can be bypassed to receive signals up to 500 MHz (external filters like the ourĀ 2mĀ filtered preamp recommended 100 MHz high pass filter recommended).

With the external ExtIO library the ColibriNANO can be used with third party software like HDSDR etc.

This is not a cheap USB dongle found on Ebay, this high performanceĀ SDR receiver is developed by Expert Electronics and features a sturdy aluminium chassis, ESD protection, USB 2.0 interface and a qualityĀ SMA antenna connector.

Best of all, the ColibriNANO travels in your pocket and only needs your computer and an antenna! Its the ultimate portable SDR receiver!

Remote Control

The ColibriNANO can be controlled via Internet usingĀ ExpertRemote, Ā aĀ client-server system thatĀ allows you to place the receiver and server inĀ a remote quiet location with good RX antennas and control and listenĀ from any place where you have an internet connection available. The receiver’s software can be synchronized with transceivers and be used as aĀ panadapter with high resolution.

Software support

  • ExpertSDR2
  • CW Skimmer
  • Skimmer Server
  • Third party software using ExtIO library

ColibriNANO Architecture

 

ColibriNANO Specifications

RF ADC, bit @ MHz 14 @ 122.88
ADC type ADS4145
RX Frequency range, MHz 0.1…55
Undersampling, MHz 0.1…500
Independent software receivers 1 + 1 SubRX
Sample rate, kHz @ bit 48; 96; 192; 384; 768 @ 24
1536; 1920; 2560; 3072 @ 16
Bandscope, MHz
RX HF filters, MHz LPF: 55
Noise floor, dBm 1.9 MHz (160M) – 131
7.1 MHz (40M) – 130
52.5 MHz (6M) – 127
NPR (Noise Power Ratio) with Noise Bandwidth 5 MHz, dB 59
BDR on HF, dB 110
BDR on VHF, dB n/s
Sensitivity, uV 0.35
DR IMD3, not less dB 95
RMDR, dB 104
ATT/Preamp, dB from -31.5 to +6, with 0.5 step
Local oscillator TCXO, MHz +/- ppm 122.88 +/- 0.5
Built-in audio codec, bit
RF input with up to 15 kV ESD protection 1 SMA connector
Maximum antenna input voltage, without ADC overload, mV (ATT=0 dB) 74 (Pk-Pk); 32.7 (RMS)
PC interface USB 2.0
DC voltage range, V 4.5…5.5
Current consumption, A 0.41
Power consumption, W 2.02
Operating temperature, Ā°C/Ā°F 0…+50/ +32…+122
Active device temperature, Ā°C +45…+50
Dimensions L x W x H, cm/inches 9.0 x 2.5 x 1.7/ 3.54 x 0.98 x 0.67
Weight, kg/lbs 43 gr/ 1.52 oz

* MoreĀ modes can be supported via external software

Specifications are subject to change without notice or obligation and specifications are only guaranteed within the amateur radio bands.

Recommended Accessories

Read more about ColibriNANO here.

SKU: ColibriNANO Categories: , Tag:
Weight 0.05 kg
Dimensions 11 × 3.5 × 3 cm

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “ColibriNANO USB SDR Receiver 0.1 to 55 MHz”

There are no reviews yet.